CYCO 360A / 360B - 3D Rotary Tank Cleaning Nozzle
- 360° Full Coverage, No Blind Spots Inside Tanks
- Dual-Axis Rotation, Precise 3D Cleaning Path
- High-Impact Jets, Remove Tough Residues
- Low Fluid Loss, Dynamic Sealing Design
- Up to 30m Coverage, Ideal for Large Tanks
- 316L Stainless Steel, Built for Harsh Environments
Product Overview:
CYCO 360 Series rotary tank cleaning nozzle is a gear-driven rotary tank washer designed for medium and large industrial tanks. The 360 series is available in two models: 360A and 360B.
360A and 360B are high-performance, gear-driven rotary tank cleaning nozzles engineered for large industrial tanks ranging from 8 to 30 meters in diameter. Driven entirely by fluid pressure, the dual-axis (X + Y) rotation mechanism covers 100% of the tank interior in every cleaning cycle, with no blind spots, no manual entry required.
Choose the 360A for tanks up to 20m with a 2″ BSP/NPT male connection, or the 360B for heavy-duty cleaning up to 30m with a higher flow capacity and 2″ female / 2-1/2″ quick-disconnect fitting.
How It Works:
Gear-Driven 3D Rotary Cleaning Technology
When cleaning liquid enters the nozzle body, it drives an internal turbine and gearbox assembly.
The gearbox controls two simultaneous movements:
- Rotation around the horizontal axis
- Rotation around the vertical axis
This motion creates a dense, woven cleaning pattern that gradually covers the entire vessel interior.
Unlike static spray balls that rely primarily on rinsing action, the CYCO 360 series generates high-impact jet streams capable of removing stubborn residues and product buildup.
Key Features:
- 100% Dead-Zone-Free Cleaning
Simultaneous axial and radial rotation traces a precise crisscross pattern across every point of the tank wall, eliminating blind spots that fixed spray balls and single-axis nozzles cannot reach.
- Minimized Fluid Loss, Only 3% Leakage
Dynamic seals at all leakage points keep cleaning fluid loss below 3%, reducing chemical consumption and water usage while maintaining higher jet impact pressure where it matters.
- Protected Gearbox for Long Service Life
An independent, enclosed gearbox isolates internal gears from the cleaning fluid. This prevents corrosion and contamination-induced wear, significantly extending maintenance intervals.
- High-Impact Concentrated Jet
A flow-stabilizing internal structure condenses the spray into a focused, high-velocity solid stream, delivering greater mechanical impact force compared to conventional hollow-cone spray balls.
- Fast Cleaning Cycles: 5–35 Minutes (360A) / 10–30 Minutes (360B)
Predictable, repeatable cleaning performance reduces tank downtime. Ideal for high-frequency CIP (clean-in-place) applications in food, beverage, and pharmaceutical production.
- 316L SS + PPS + Rulon Construction
All wetted parts use corrosion-resistant 316L stainless steel, with PPS and Rulon specialty engineering materials for seals, compatible with water, weak acid solutions, and weak alkali cleaning media.
Technical Specifications:
Parameter | 360A | 360B |
Tank Diameter | Up to 20m | Up to 30 m |
Working Pressure | 3–15 bar | 3–22 bar |
Recommended Pressure | 4–14 bar | 4–20 bar |
Flow Rate | ~80–280 L/min | ~150–1,100 L/min |
Cleaning Cycle | 5–35 min | 10–30 min |
Connection | 2″ BSPT/NPT Male (External) | 2″ BSPT/NPT Female or 2-1/2″ Quick Disconnect |
Tank Opening Required | ≥ Ø290 mm | > Ø320 mm |
Weight | 5.1 kg | 11.6 kg |
Best For | Medium-large tanks, breweries, food tanks | Large industrial tanks, chemical/petrochemical vessels |
Not sure which model fits your application? Send us your tank diameter, working pressure, and cleaning media, and our engineers will recommend the right configuration within 24 hours.
360A Technical Specifications:
Parameter | Specification |
Materials | 316L Stainless Steel, PPS, Rulon Specialty Engineering Materials |
Cleaning Media | Water, weak acid solutions, weak alkali solutions |
Working Pressure | 3–15 bar |
Recommended Pressure | 4–14 bar |
Max Operating Temperature | 95°C |
Max Ambient Temperature | 120°C |
Cleaning Angle | 360° |
Cleaning Cycle | 5–35 minutes |
Cleaning Diameter | Up to 20 m |
Tank Opening Required | ≥ Ø290 mm |
Connection | 2″ BSPT/NPT External Thread (Male) |
Weight | 5.1 kg |
360B Technical Specifications:
Parameter | Specification |
Materials | 316L Stainless Steel, PPS, Rulon Specialty Engineering Materials |
Cleaning Media | Water, weak acid solutions, weak alkali solutions |
Working Pressure | 3–22 bar |
Recommended Pressure | 4–20 bar |
Max Operating Temperature | 95°C |
Max Ambient Temperature | 120°C |
Cleaning Angle | 360° |
Cleaning Cycle | 10–30 minutes |
Cleaning Diameter | Up to 30 m |
Tank Opening Required | > Ø320 mm |
Connection | 2″ BSPT/NPT Female Thread or 2-1/2″ Quick Disconnect Fitting |
Weight | 11.6 kg |
Performance Curves:
360A — Flow Rate vs Working Pressure
Flow rate ranges from approximately 80 L/min at 3 bar to 280 L/min at 15 bar, depending on nozzle orifice size (φ6 to φ10). Select a larger orifice for higher flow; select a smaller orifice for greater jet concentration and impact at the same pressure.
360A — Cleaning Diameter vs Working Pressure
Effective cleaning diameter increases from ~4 m at 3 bar to up to 15 m at 17 bar (orifice φ10). For tanks near the maximum 20 m diameter, a working pressure of 14+ bar is recommended.
360B — Flow Rate vs Working Pressure
The 360B rotary tank cleaning nozzle delivers flow rates ranging from approximately 150–300 L/min at 2.8 bar up to 450–1,100 L/min at 15 bar, depending on nozzle orifice configuration.
Seven orifice size combinations are available (2-φ7.14 through 2-φ15.9), allowing precise flow matching to your supply system:
- 2-φ7.14 (smallest): ~150 L/min @ 2.8 bar → ~450 L/min @ 15 bar
- 2-φ15.9 (largest): ~300 L/min @ 2.8 bar → ~1,100 L/min @ 15 bar
For applications with limited pump capacity, smaller orifice configurations maintain effective cleaning impact at lower flow rates.
360B — Cleaning Diameter vs Working Pressure
Effective cleaning diameter increases with supply pressure across all nozzle configurations:
- At 2.8 bar, all configurations start at approximately 4–5 m cleaning diameter
- At 15 bar, cleaning diameter ranges from 8 m (2-φ7.14) to 35 m (2-φ15.9)
- The 2-φ15.9 configuration reaches the 360B’s rated 30 m cleaning diameter at approximately 13 bar
For tanks in the 20–30 m range, a working pressure of 10 bar or above is recommended to ensure thorough wall coverage.
Applications:
CYCO 360A/360B 3D rotary tank cleaning nozzles are trusted in demanding cleaning environments across multiple industries:
- Breweries & Wineries — Removes yeast residue, tartrate deposits, and fermentation byproducts from fermentation tanks and storage vessels
- Food & Beverage Processing — Meets hygienic cleaning requirements for mixing tanks, pasteurization vessels, and juice/dairy storage tanks
- Chemical & Petrochemical — Cleans reactors and storage tanks containing viscous residues, polymer deposits, or corrosive liquids
- Fuel Ethanol & Industrial Fermentation — High-impact jet effectively removes sticky fermentation residue in large-volume vessels
- Pharmaceutical & Biotech — CIP-compatible design supports GMP-compliant cleaning validation for bioreactors and blending tanks
- Tank Trucks & Road Tankers — Compact installation through standard manways; cleans tanker interiors in transit depots
- Papermaking & Pulp — Handles fiber-laden slurry residues in process tanks
Not sure which model, nozzle size, or pressure setting fits your tank? Our application engineers have helped clients across breweries, chemical plants, and pharmaceutical facilities configure the right cleaning solution. Share your requirements, typical response within 24 hours.
FAQs
Q1. What tank size can the 360 Series clean?
The 360A model can clean tanks up to approximately 20 meters, while the 360B model is suitable for tanks up to 30 meters in diameter.
Q2. Can it replace manual tank cleaning?
Yes. The nozzle is designed to eliminate the need for personnel entering the tank for routine cleaning operations.
Q3. Is it suitable for CIP systems?
Yes. The 360 series rotary tank cleaning nozzle is commonly integrated into automated CIP systems in food, beverage, pharmaceutical, and chemical industries.
Q4. What materials are available?
Standard construction includes 316L stainless steel and engineering-grade polymer components.
Q5. What pressure is recommended?
For optimal cleaning performance:
- 360A: 4–14 bar
- 360B: 4–20 bar
Related Products
